Concrete cutting in Milford CT - clean, straight openings right where you need them
Need a trench for a drain line or a bad section cut out of your slab? We make clean, straight cuts where you mark them.
- Fully licensed and insured.
- Free on-site estimates.
- Replies within 1 business day.
When do you need concrete cut, and how does it work?
Concrete cutting in Milford means sawing straight lines through a slab or wall, or drilling round holes, so you can run a pipe, open a trench or take out a damaged piece without tearing up everything around it.
Usually the cut is the first step of something bigger, like a drain line through a garage floor or a cracked panel coming out before we pour a new section of concrete driveway. The price moves with how thick the concrete is, how much steel is in it, how many feet of cut or how many holes you need, and whether you want the pieces broken up and hauled away or left where they sit. The schedule mostly turns on where the cut is, because work in a curb, sidewalk or driveway apron needs the city's okay first, and we take care of that. When I come out, I measure it all and put it in a written estimate so you can see each part of the job.
How do you know it's time to cut instead of patch?
One section cracked and sunk
One piece of your driveway or walk has cracked and dropped while the rest sits fine. Usually the ground under that piece washed out or settled, and cutting it out cleanly lets us fix just that part before the trip edge gets worse and water works under the good concrete.
New plumbing under the floor
Your plumber needs a drain or line run under a basement or garage slab. A sawed trench with straight edges patches back far better than a hole chipped out by hand, and leaving it until the plumber is standing there usually means a rushed, ragged cut.
A pipe or vent through concrete
You need a dryer vent, conduit or pipe through a foundation wall or floor. A drilled round hole keeps the concrete around it sound, while one knocked out with a hammer tends to crack the edges and leave gaps you'll be sealing for years.
How we handle concrete cutting, start to finish
We start by looking at what's being cut, how thick it is and what's around it, since that picks the saw and the blade. If there could be rebar, the steel bars set inside concrete to hold it together, or pipe running through it, we talk through whether scanning makes sense before we cut, and on a slab or wall that carries weight it may be needed. Before the saw starts we also agree with you on who handles the slurry. Then we snap the lines, make the cuts, and either leave the panels in place or break them up and haul them off, whichever you picked at the estimate.
Most cuts end with a pour. When a cracked section of driveway comes out we can pour the replacement, or if the rest of it is worn out too, move on to full concrete driveway building. The same saws cut control joints, the shallow grooves that give a new slab a planned place to crack, on the slabs we pour for concrete patio construction.
Slab cuts with a flat saw
For driveways, garage floors, patios and walks, a walk-behind flat saw runs a straight line across the slab. It's the right tool for drain trenches and for cutting out a damaged section.
Walls and tight spots
A wall saw runs on a track for straight cuts through a foundation wall, and a hand saw gets into corners and steps where nothing bigger fits. Thick or heavily reinforced sections can call for a wire saw instead.
Round holes for pipe and drains
When you need a vent, drain or conduit through a wall or floor, a drilled hole leaves clean edges that seal up well. It suits plumbing and electrical work that only needs a pass-through, not a trench.
Get a written estimate for your concrete cut
Send the form and we'll reply within one business day to set up a free on-site visit. I come out, measure the cut and give you a written estimate, with no obligation to book.
Call (475) 549-2244- Based in
- Milford, CT 06461
- Hours
- Mon–Fri: 6 AM–9 PM, Sat–Sun: 8 AM–10 PM
What happens after you call us about a cut?
Here's how a cutting job runs from your first call to the final walk-through, and who you'll be dealing with at each step.
Call or send the form
You reach us by phone or the form, and we get back to you to set up a visit. It helps to tell us where the cut is, what surface it's in and whether you want the pieces hauled off.
I look at the site
I come out myself, measure the concrete, check what's around it and ask what the opening is for. You get a written estimate that spells out the cutting, any scanning, the removal and the slurry cleanup, so you know what each part covers.
We handle the city steps
Once you give the go-ahead, we take care of the city steps the cut calls for. Inspections on Milford curb, sidewalk and apron permits need 24 hours' notice, so we plan your date around that.
We cut and walk it
Our crew makes the cuts and handles the pieces and slurry the way we agreed. Then we walk the finished job with you before we leave.
Why homeowners call Premier Milford Concrete for concrete cutting
I look at every job
I come out to measure every cut before you see a number, and I do the work with our crew. The person who looked at your slab is the one answering for it, so nothing gets lost between the estimate and the saw.
Licensed and insured on every cut
We're fully licensed and insured. A saw through concrete can hit what's inside or nick what's next to it, so you want that covered before anyone starts the blade.
Straight answers since 2023
I spent my summers on concrete crews and started this business in 2023, and most of our calls come from homeowners in Milford and the cities nearby. I'd rather tell you plainly what your cut needs than sell you scanning or removal you don't.
The cut itself is quick work once you know what's inside the concrete and where the mess goes. Send us the details or call (475) 549-2244 and I'll come take a look.
Concrete cutting, driveways and patios in Milford
Cuts in a curb, sidewalk or driveway apron in Milford go through the city's Engineering Department, which approves that work and requires a permit for anything beyond ordinary repairs. The permit has to be in hand before work starts, and the application asks for a Call Before You Dig ticket number, so that call comes first. Whether your cut counts as an ordinary repair is the city's decision, so we check at the start, and when a permit is needed we handle the application and set up the inspections. At the estimate I'll tell you what the city will want from you.
We're based in Milford and work across the cities around it, and a lot of what we cut here is older driveways and walks where one section settled while the rest held. Older slabs can hide steel or old lines nobody wrote down, so we ask what you know about the house before picking a spot, the same as we do on jobs in Stratford and Orange.
Questions about concrete cutting in Milford
Call (475) 549-2244How much does concrete cutting cost in Milford?
Concrete saw cutting across the US usually costs about $4 to $15 per linear foot, and that covers the sawing alone. Reinforced or thicker slabs cost more per foot than an easy 4- to 6-inch slab, and a small job is often priced by its minimum or setup charge, so a short cut can cost more than its length suggests. Your written estimate gives you the number for your own cut.
Does the price of concrete cutting include removing the concrete?
Often it doesn't, because sawing and removal are separate jobs and a cutter can make the lines and leave the panels in place. Breaking, lifting, hauling and disposal can add more than the sawing itself, so compare quotes on what each one includes. We write removal on the estimate so you can see it and decide.
Who can pull a sidewalk or driveway apron permit in Milford?
Only a contractor licensed with the City of Milford can pull its sidewalk, curb and driveway apron permits. That city license requires a State of Connecticut contractor's license, so ask any cutter whether they hold both before they work near the street.
What happens to the slurry when concrete is cut?
Slurry, the wet gray paste a water-cooled blade leaves behind, gets collected and taken away by whoever you've agreed will handle it. A concrete sawing trade group's spec says that collection and disposal must be planned by agreement with the owner before work starts, so we settle it with you before the first cut.
What is the best way to cut a hole in concrete for a pipe?
Core drilling is the usual way to make a round hole for a pipe, drain or conduit, using a hollow bit that cuts a clean circle. Holes are priced separately from straight saw cuts, so if you need both, ask to see them as separate lines on your quote.
How do I keep the rest of my driveway from cracking when a section is cut out?
Saw it out instead of breaking it out, because a clean saw line stops at the edge instead of sending cracks into the good concrete. Then the new piece needs its base dug out and packed, since the soft ground that sank the old section will sink the new one too. If the budget is tight, I'd spend it on that base before any fancy finish.
Concrete work that often follows a cut
Concrete driveway building
When a cracked or sunken driveway is past patching, a full tear-out and new pour over a packed base gives you a surface you can trust again.
Concrete patio construction
If you're opening up the backyard, a new patio slab poured over a dug-out base gives you a solid, even place to sit, grill and gather outside.
Service areas for concrete cutting near Milford
Premier Milford Concrete is based in Milford, CT, and we take cutting jobs across the 12 areas listed below, including Bridgeport and West Haven. These are the cities with their own page, not the only places we work.
Milford, CT
Tell us where your concrete needs cutting
Call (475) 549-2244 or send the form with the cut's location, the surface and whether you want the pieces hauled away, and I'll show up ready to measure.